Sena LS100 Manual de usuario

1HelloDevice Lite SeriesLS100User GuideVersion 1.4.42011-12-12

10Figure 2-1 The panel layout of the LS1002.2 Connecting The HardwareThis section describes how to connect the LS100 to serial device for the first ti

11Figure 2-2 Connecting the power to the LS1002.2.2 Connecting To The NetworkConnect the one end of the Ethernet cable to the LS100 10Base-T port and

122.2.3 Connecting To The DeviceConnect the serial data cable between the LS100 and the serial device. If necessary, supply thepower to the serial dev

132.3.1 Using Serial Console1) Connect the one end of the serial console cable to the serial port of the LS100.Figure 2-5 Connecting a serial console

146) Type the user name and password to log into the LS100. A factory default setting of theuser name and password are both admin.7) If the user logge

151) Run a telnet program or a program that supports telnet functions such as TeraTerm-Pro orHyperTerminal. The target IP address and the port number

16get [group] + <CR> Get configuration parameter values- group = 'ip', 'host', 'serial', 'admin' or &apo

17next indicates the default gateway IP address.If users want to change only one of the parameters of the group, users can omit trailing parametersand

18The group means the category where parameters belong to as like ‘set’ command. For example, ifusers want to view parameter values related to IP conf

192.4.3 ‘help’ CommandWith ‘help’ command, users can find command usage help in the console screen. Basic commandusage is as follows:help [group] + &l

2User Guide for the HelloDevice LS100Version 1.4.4Firmware version 1.4.XLast revised on Dec 12, 2011Printed in KoreaCopyrightCopyright 2002-2012, Sena

202.4.4 ‘factorydefault’ CommandWith ‘factorydefault’ command, users can load factory default parameter values in console. Commandusage of ‘factorydef

212.4.7 ‘reboot’ CommandWith ‘reboot’ command, the LS100 will be rebooted immediately. Changed parameter values will beapplied when the LS100 is up ag

223: IP Address ConfigurationA valid IP address of the LS100 needs to be assigned before it starts to work in the user's networkenvironment. A ne

233.1 Static IP3.1.1 OverviewIn the Static IP mode, users have to manually specify all the parameters such as IP addresses of theLS100, valid subnet m

24> set ip static 192.168.1.10 255.255.255.0 192.168.1.1OKFigure 3-1 Setting IP configuration parameters for Static IP mode3.2 DHCP3.2.1 OverviewDy

253.2.2 DHCP ConfigurationTo make the LS100 work in DHCP mode, just set IP mode to DHCP as in Figure 3-2.> set ip dhcpOK>Figure 3-2 Setting DHCP

263.4 IP FilteringThe LS100 has an IP address based filtering feature to prevent unauthorized remote hosts fromaccessing LS100. The user can allow one

274: Host Mode ConfigurationHost mode represents the operating session mode of the LS100. Several host modes are available forthe data communication b

28set host hostmode par1 par2 ...where,hostmode: tcps=TCP server / tcpc=TCP client / tcpsc=TCP server & clientparameters:if hostmode = TCP server

29 Sync-SentIf the LS100 sends a connection request to a remote host, the state is changed from [Closed] to[Sync-Sent]. This state is maintained unti

3Contents1: Introduction 51.1 Overview ...

302) Operations Serial data transferWhen a session has been established, the LS100 reads the data from the serial port buffer tillinternal serial buf

314.1.2 TCP Server Mode ConfigurationTo configure the LS100 to work as a TCP server, use ‘set’ command as follows:set host tcps listening_TCP_port ina

324.2 TCP Client Mode Operations4.2.1 OverviewThe LS100 works as a TCP client, and the default TCP state is [Closed] in this mode. The remote hostwill

33 Cyclic ConnectionIt Cyclic Connection function is enabled, the LS100 will make an attempt to connect to the user-defined remote host at certain in

344.2.2 TCP Client Mode ConfigurationTo configure the LS100 to work as a TCP client, use set command as follows:set host tcpc dest_ip dest_port cyclic

35[Listen] --> [Sync-Sent] --> [Established] --> [Data] --> [Closed] --> [Listen]The initial state is [Listen]. If there are data comin

364.3.2 TCP Server/Client Mode ConfigurationTo configure the LS100 to work as a TCP server/client mode, use ‘set’ command as follows:set host tcpsc li

375: Serial Port ConfigurationTo attach the serial device to the LS100 serial port, its serial port operation should match exactly tothat of the seria

38The factory default setting of the flow control is None. Only hardware flow control using RTS/CTS issupported by the LS100. Hardware flow control me

39> set serial 9600 7 e 2 h s n 10OK>Figure 5-1 Serial port configuration

44.1.2 TCP Server Mode Configuration...314.2 TCP Client Mode Operati

406: System AdministrationUsers can configure administrator username, password and device name using set command asfollows:set admin username password

41Appendix A: ConnectionsA.1 Ethernet PinoutsThe LS100 uses standard Ethernet connector, which is a shielded connector compliant with AT&T258speci

42A.3 Ethernet Wiring DiagramFigure A-3 Ethernet direct connection using crossover ethernet cableFigure A-4 Ethernet connection using straight through

43Appendix B: Well-known Port NumbersThe port numbers are divided into three ranges: the Well Known Ports, the Registered Ports, and theDynamic and/or

44Appendix C: TroubleshootingC.1 Power/LED Status TroubleshootingProblem Cause ActionPower LED doesnot light upPower cable is notconnectedCheck power

45Cannot login toconsoleInvalid username and/orpasswordUse valid username and password. If username and/orpassword are lost, perform factory default r

46C.7 Serial Communication TroubleshootingProblem Cause ActionSerial data are nottransferred byTCP/IP immediatelyToo large inter-charactertimeoutSet i

47Appendix D: WarrantyD.1 GENERAL WARRANTY POLICYSena Technologies, Inc. (hereinafter referred to as SENA) warrants that the Product shall conform toa

48D.3 HARDWARE PRODUCT WARRANTY DETAILSWARRANTY PERIOD: SENA warranties embedded hardware Product for a period of one (1) year,and external hardware P

51: Introduction1.1 OverviewThe HelloDevice Lite Series allows you to network-enable a variety of serial devices that were notoriginally designed to b

61.3 Product SpecificationOne male DB9 serial port for data communication/serial consoleSerial speeds 1200bps to 115200bpsFlow Control: None, Hardware

71.4 Terminologies And AcronymsThe Internetworking related terminologies used frequently in this manual are defined clearly to helpyour better underst

8Table 1-1 Acronym TableISPInternet Service ProviderPCPersonal ComputerNICNetwork Interface CardMACMedia Access ControlLANLocal Area NetworkUTPUnshiel

92: Getting StartedThis chapter describes how to set up and configure the LS100 in the first place.- 2.1 Panel Layout explains the panel layout and LE