Sena STS Series Guía de usuario Pagina 22
- Pagina / 131
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
22
3. Network Configuration
3.1. IP Configuration
The STS Series requires a valid IP address to operate within the user’s network environment. If the
IP address is not readily available, contact the system administrator to obtain a valid IP address for the
STS Series. Please note that the STS Series requires a unique IP address to connect to the user’s
network.
The users may choose one of three Internet protocols in setting up the STS Series IP address: i.e.,
Static IP
DHCP (Dynamic Host Configuration Protocol)
PPPoE (Point-to-Point Protocol over Ethernet)
The STS Series is initially defaulted to STATIC mode, with a static IP address of 192.168.161.5. Table
3-1 shows the configuration parameters for all three IP configurations. Figure 3-1 shows the actual
web-based GUI to change the user’s IP configuration.
Table 3-1 IP configuration Parameters
IP address
Subnet mask
Default gateway
Static IP
Primary DNS/ Secondary DNS
DHCP
Primary DNS/ Secondary DNS (Optional)
PPPoE Username
PPPoE Password
PPPoE
Primary DNS/ Secondary DNS (Optional)
Figure 3-1 IP Configuration
- STS Series 1
- Copyright Information 2
- Trademark Information 2
- Notice to Users 2
- Technical Support 2
- Revision history 3
- Contents 4
- 5. PC Card Configuration 69 5
- 6. System Administration 74 5
- 7. System Statistics 85 5
- Appendix 8. Warranty 130 7
- 1. Introduction 8
- 1.2. Package Check List 9
- 1.3. Product Specification 9
- MAC address 10
- Session 10
- Client/Server 11
- 2. Getting Started 13
- 2.2. Connecting The Hardware 14
- 2.2.1. Connecting The Power 15
- No flow control 18
- 2.2.6. Using Remote Console 19
- 3. Network Configuration 22
- IP address 23
- Subnet mask 23
- Default gateway 23
- Primary and Secondary DNS 23
- 3.1.2. Using DHCP 24
- 3.2. SNMP Configurations 25
- sysContact: 26
- sysName: 26
- sysLocation: 26
- 3.2.4. Management Using SNMP 27
- 3.4. SMTP Configuration 29
- 3.5. IP Filtering 30
- 3.7. NFS Server Configuration 32
- 3.8. Ethernet Configuration 33
- 3.9. Web Server Configuration 33
- TCP keep-alive time: 34
- TCP “keep-alive” probes: 35
- TCP keep-alive intervals: 35
- 4. Serial Port Configuration 36
- 4.2.1. Port Enable/Disable 40
- 4.2.2. Port Title 40
- TCP mode 42
- UDP mode 42
- Modem emulation mode 42
- Serial data transfer 44
- Session disconnection 44
- TCP listening port 44
- User Authentication 45
- Telnet protocol 45
- Max. allowed connection 45
- Cyclic Connection 45
- Inactivity Timeout 46
- Socket ID 46
- TCP Nagle algorithm 47
- UDP receiving port 47
- Check the certificate CN 55
- Length 56
- Key Block(32-byte) 57
- Key (24-byte) IV(8-byte) 57
- 4.2.9. Serial Port Parameters 58
- Parity 59
- Stop bits 59
- Flow control 59
- DTR/DSR behavior 60
- Inter-character timeout 60
- 4.2.10. Modem Configuration 61
- 4.2.11. Port Logging 62
- Figure 4-18 65
- SNMP trap community 65
- 4.3. All Port Configurations 67
- Port enable/disable 68
- Port title 68
- Host mode 68
- 5. PC Card Configuration 69
- 5.1. LAN Card Configuration 70
- 6. System Administration 74
- System log buffer size 75
- 6.3. User Logged On List 76
- 6.4. Change Password 76
- 6.6. User Administration 77
- 6.7. Date And Time Settings 78
- 6.8. Configuration Management 79
- 6.9. Firmware Upgrade 80
- 6.10. User File Uploading 82
- 7. System Statistics 85
- 7.3. IP Statistics 86
- 7.4. ICMP Statistics 88
- 7.5. TCP Statistics 90
- 7.6. UDP Statistics 92
- 8. CLI guide 93
- 8.3.2. File And Disk Utils: 94
- 8.3.3. System Utilities: 94
- 8.3.4. Network Utilities: 94
- 8.7. File Transmission 96
- 8.8. Examples 96
- 9. User Customization Guide 99
- 9.3. User Defined Web Pages 100
- Appendix 1. Connections 101
- HelloDevice 102
- Remote Host 102
- RJ45-DB25 female adapter 103
- RJ45-DB25 male adapter 103
- Table A-3 Network card 104
- Table A-6 Serial Modem Card 105
- A 3.1. system.cnf 106
- A 3.2. redirect.cnf 108
- A 5.1. Overview 113
- A 5.2. Main Menu 113
- A 5.3. RTC Configuration Menu 113
- A 5.4. Hardware Test Menu 114
- A 5.5. Firmware Upgrade Menu 118
- Appendix 8. Warranty 130
Relacionado con productos y manuales para Redes Sena STS Series
Redes Sena ProBee-ZS10 Guía de usuario
(66 paginas)
(66 paginas)
Redes Sena PS200 Guía de usuario
(68 paginas)
(68 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales